siv1987 Posted February 16, 2014 Share Posted February 16, 2014 Can someone please help me. I am using a newly digitized embroidery design, and it has sewed out perfectly for me about the first 5 times. All of a sudden there are problems with it. Have tried different hoops, backing, changed thread, bobbin thread, needle, everything.Then it sews again good 1 or 2 times, and back to the same old stuff. Am using the same exact shirts to sew this design on. Has anyone had this problem before?& Would appreciate any help. I have a Tajima TEHX-C1501. 1 Quote Link to comment
test8 Posted February 19, 2014 Share Posted February 19, 2014 I have been using my laptop and Linksyc modem to run machine Neo2 and not it isn't working can someone help me. Also can I buy a serial cable from Microcenter as I am in a hurry and use it to run. If so what settings on the machine would I need to change. It is set on Lan now 1 Quote Link to comment
sevigine Posted February 19, 2014 Share Posted February 19, 2014 You would need to get the serial cable from your distributor. A standard cable from a computer store will not work. I think yoou have been speaking with a support tech about this. I am going to contasct our support team to see what I can do to help. Best Regards, 1 Quote Link to comment
siv1987 Posted February 22, 2014 Author Share Posted February 22, 2014 Need a suggestion. my lan quit working on our TFMX 1501C a few months back, Hirsh says call pulse and pulse says call Hirsh. and neither can get it working again. it just doesn't see the machine. any ideas or suggestions for escalating the Trouble ticket. 1 Quote Link to comment
patz333 Posted March 12, 2014 Share Posted March 12, 2014 I need to sell my embroidery machines. I have 2 Tajima TFMX-C1501 Commercial machines and I owe $25,000.00 total. Please contact with me if you are interested. 1 Quote Link to comment
jdemyers Posted June 20, 2014 Share Posted June 20, 2014 Is there a way to get the TEJT Neo embroidery machine to recognize the pulse stop command? 1 Quote Link to comment
diver361 Posted June 23, 2014 Share Posted June 23, 2014 Is there a way to get the TEJT Neo embroidery machine to recognize the pulse stop command? Only software way, don't need have commercial pack, just need Ambassador free editor or Embird (editor) 1 Quote Link to comment
Berez Posted October 6, 2014 Share Posted October 6, 2014 Does anyone know how to put a stop in the machine for doing applique? Were putting on numbers and their all different. Were standing here watching the machine to make it stop. I am sure we are wasting our time. Need some advise. Thanks:) 1 Quote Link to comment
mmoore114 Posted October 6, 2014 Share Posted October 6, 2014 Does anyone know how to put a stop in the machine for doing applique? Were putting on numbers and their all different. Were standing here watching the machine to make it stop. I am sure we are wasting our time. Need some advise. Thanks:) 1. Run the design and stop the machine at where you want to stop for an applique. If you have many places for applique stop, continue to do this. 2. Check the stitch number(s) at stopping position(s) on the machine panel. (remember the stitch number) 3. After the embroidery ends, start Design editing on the machine panel (stitch modification). 4. In the editing, go to the stitch (you remembered the stitch number). 5. Insert a Stop code (command) at the stitch number. (If you have many places, repeat 4 and 5.) When you add Stop code(s), you have to set up additional color changes. If you added one Stop code, you may need one more color change. The machine just stops when the same needles are set at before and after a Stop code. (it doesn't change color automatically and start automatically even you set up the machine with auto-color change and auto-start function) For example, Ndl#1- Stop - Ndl#2 - Stop - Ndl#2 - Stop - Ndl#3 - End At the 2nd Stop, the machine just stops but no color changing and no start sutomatically. Please read your user's manual of TEHX carefully for stitch modification. If you need more information please contact your Tajima distributor. 1 Quote Link to comment
Berez Posted October 6, 2014 Share Posted October 6, 2014 Thank you very much for your information. I can better understand the instruction book with your information. 1 Quote Link to comment
mmoore114 Posted October 16, 2014 Share Posted October 16, 2014 Trying to connect via a serial cable to a Tajima TEHX-C1501 Does anyone know how to set up the serial cable connect via the software? I can get it to recognize the machine but it won't send anything to it. I get an error of "fff". Any help would be greatly appreciated 1 Quote Link to comment
Carol1950 Posted October 16, 2014 Share Posted October 16, 2014 I'm guessing you got this fixed it has been over a month. We are getting the same error what did you do? Quote Link to comment
mazdakathy Posted February 20, 2015 Share Posted February 20, 2015 A Query About Embroidery machine also email me with prices and sizes of that you stock at the moment?? Regards 1 Quote Link to comment
ramages Posted December 6, 2015 Share Posted December 6, 2015 Give me some address of embroidery machines unit's where is the location in Munich I can't find it 1 Quote Link to comment
Ventsislav Posted December 14, 2019 Share Posted December 14, 2019 Hello guys, can somebody of you can help me? I have Tajima TMFX C1204, it’s very old embroidery machine that hasnt been used for years. I want to work with this machine again but it says we have a problem with the software and the BIOS. I need new software for my machine and also the BIOS doesn’t work so I can’t find neither the software also how to upload it. Can somebody of you help me to solve it? appreciate your time guys 1 Quote Link to comment
PLATINUM DESIGN Posted April 6, 2020 Share Posted April 6, 2020 On 12/14/2019 at 7:57 AM, Ventsislav said: Hello guys, can somebody of you can help me? I have Tajima TMFX C1204, it’s very old embroidery machine that hasnt been used for years. I want to work with this machine again but it says we have a problem with the software and the BIOS. I need new software for my machine and also the BIOS doesn’t work so I can’t find neither the software also how to upload it. Can somebody of you help me to solve it? appreciate your time guys Hi Ventsislav, I came across your post today, hopefully you've been able to get your Tajima up and running.....if not or if you have a problem down the road, I would like to suggest calling "Hirsch"...open an account to create a customer number with your name/company name and the Tajima run (it's not a credit account...you don't have to buy anything)...... We bought a used Tajima from a private party and at one point we were having issues....I called Hirsch to order the parts we needed (fixed knife, under thread presser & movable knife)....the parts arrived, my husband who is a very diy and mechanically inclined guy installed the new parts and for some reason things were not working right, after trying for a couple hours I decided to call Hirsch, they were awesome, they emailed directions over and put a message in for one of their service guys to call us.....their service guy called and was on the phone with my husband for over an hour and even called back the next day, which was a SATURDAY!! to make sure that we got everything running right....The only thing we had to pay for were the parts!! Service guy was a life saver!! Hirsch 1-800-394-4426 Good luck with everything Susan Quote Link to comment
DebBees Posted January 5, 2021 Share Posted January 5, 2021 I put on cap frame and as soon as the needle goes down it breaks needles on both heads. Why. I did stitched out design first and it was running good. 1 Quote Link to comment
diver361 Posted January 30, 2021 Share Posted January 30, 2021 On 1/5/2021 at 2:07 PM, DebBees said: I put on cap frame and as soon as the needle goes down it breaks needles on both heads. Why. I did stitched out design first and it was running good. Change needle, may be it curve? 1 Quote Link to comment
luigi Posted February 13, 2021 Share Posted February 13, 2021 TEHX-c1501 prima mi faceva un rumore come fosse un pass pass poi lo spenta e lo riaccesa e mi esce il software e mi rimane bloccato con M: V0.5 e non si muove nessun tasto cosa fare grazie tajima.mp4 1 Quote Link to comment
diver361 Posted February 13, 2021 Share Posted February 13, 2021 Strang error code. I not fount it in my manual. A Also ask my friend. Quote Link to comment
luigi Posted February 14, 2021 Share Posted February 14, 2021 io non penso sia un codice di errore si dovra rimettere il software almeno che quando faceva rumore non si e staccata o spostato qualche spinetta ti faccio una foto della accensione esce cosi e poi va in questaltra foto e non mi funziona niente grazie Quote Link to comment
luigi Posted February 14, 2021 Share Posted February 14, 2021 FECI UN VIDEO LO TROVATO E LO POSO X IL DIFETTO 80548111_VIDEODIFETTO.mp4 1 Quote Link to comment
e ran Posted April 5, 2021 Share Posted April 5, 2021 Hello room. Can someone help me please? I just bought a used Tajima tehx c1501 and I am breaking needles. The needle is off center from the bobbin hole just a tab bit like 2-3 millimeters and it is hitting the face plate, once it starts a job the needle breaks instantly. I adjusted the main shaft handle to align directly over the hole but once I began a job it moves slightly over to the left again. I feel like its something minor but it major for me and I don't know what to do. Thanks Quote Link to comment
Recommended Posts
You can post now and register later. If you have an account, sign in now to post with your account.